Respvr

respvr@retaqs.com

123 discussions

RE: [Respvr] Start Up sequence
by MCKINNEY, MICHAEL R 07 Jun '06

07 Jun '06

ANO-1 has non-trippable axial power shaping rods. ANO-1 also unscrews the rods, vs jacking them out. -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of ALDAY, CLINT L Sent: Wednesday, June 07, 2006 12:26 PM To: RE Supervisors Subject: RE: [Respvr] Start Up sequence Non-trippable rods? Clint Alday 504-739-6331 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of POHL, MATTHEW H Sent: Monday, June 05, 2006 7:22 PM To: RE Supervisors Subject: RE: [Respvr] Start Up sequence Fort Calhoun normally dilutes to within 100 ppm of ECC boron, then withdraws Shutdown Banks A & B, dilutes the remaining 100 ppm to ECC boron, withdraws the non-trippable rods, and then withdraws the Reg Rods. Matt Pohl (402)533-6820 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of Hugh_E_McKenney(a)dom.com Sent: Thursday, May 18, 2006 8:19 AM To: respvr(a)retaqs.com Subject: [Respvr] Start Up sequence RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr This e-mail contains Omaha Public Power District's confidential and proprietary information and is for use only by the intended recipient. Unless explicitly stated otherwise, this e-mail is not a contract offer, amendment, nor acceptance. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

RE: [Respvr] Start Up sequence
by ALDAY, CLINT L 07 Jun '06

07 Jun '06

Non-trippable rods? Clint Alday 504-739-6331 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of POHL, MATTHEW H Sent: Monday, June 05, 2006 7:22 PM To: RE Supervisors Subject: RE: [Respvr] Start Up sequence Fort Calhoun normally dilutes to within 100 ppm of ECC boron, then withdraws Shutdown Banks A & B, dilutes the remaining 100 ppm to ECC boron, withdraws the non-trippable rods, and then withdraws the Reg Rods. Matt Pohl (402)533-6820 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of Hugh_E_McKenney(a)dom.com Sent: Thursday, May 18, 2006 8:19 AM To: respvr(a)retaqs.com Subject: [Respvr] Start Up sequence RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr This e-mail contains Omaha Public Power District's confidential and proprietary information and is for use only by the intended recipient. Unless explicitly stated otherwise, this e-mail is not a contract offer, amendment, nor acceptance. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

RE: [Respvr] Start Up sequence
by POHL, MATTHEW H 06 Jun '06

06 Jun '06

Fort Calhoun normally dilutes to within 100 ppm of ECC boron, then withdraws Shutdown Banks A & B, dilutes the remaining 100 ppm to ECC boron, withdraws the non-trippable rods, and then withdraws the Reg Rods. Matt Pohl (402)533-6820 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of Hugh_E_McKenney(a)dom.com Sent: Thursday, May 18, 2006 8:19 AM To: respvr(a)retaqs.com Subject: [Respvr] Start Up sequence RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr This e-mail contains Omaha Public Power District's confidential and proprietary information and is for use only by the intended recipient. Unless explicitly stated otherwise, this e-mail is not a contract offer, amendment, nor acceptance. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

1 0

Re: [Respvr] MIDs questionnaire
by Bob_Tomonto＠fpl.com 22 May '06

22 May '06

Frank, In response to your question, we post an RP supervisor with I&C folks at the seal table (which is located outside the bio wall) and we run the detectors through the system. We are in continuous radio communication between the Control Room and the Containment flux map seal table. Personnel working in the area are limited by the personnel physical barrier provided by the RP group. We generally run the detectors through all of the thimbles to ensure the automatic features are working properly and we have no restrictions with regard to access through the thimbles. Any problems can be addressed by I&C in field at the time. Obviously this work is performed prior to containment closure and heatup. An RP contact is Rick Brown at (305) 246-6017. Bob Tomonto Turkey Point Reactor Engineering frank.paslaski@exe loncorp.com To: mmccutc1(a)txu.com, gary.deck(a)exeloncorp.com, dbarton(a)entergy.com, Sent by: vakhariap(a)firstenergycorp.com, klhill(a)tva.gov, ronald.niederer(a)exeloncorp.com, respvr-bounces@ret bdrichardson(a)cal.ameren.com, skip.e.winter(a)constellation.com, aqs.com bnwoolwe(a)duke-energy.com, darowland(a)aep.com, allan.hartwig(a)pgnmail.com, jafehl(a)firstenergycorp.com, CHD5(a)pge.com, JMCCORY(a)southernco.com, RTSTILL(a)southernco.com, jabozarth(a)oppd.com, scott.jackson(a)pgnmail.com, 05/19/2006 03:35 tlowe1(a)entergy.com, John.Kreeger(a)nmcco.com, ablinker(a)duke-energy.com, PM pakeller(a)duke-energy.com, douglas_l_vining(a)dom.com, dennis_m_russo(a)dom.com, Please respond to robert_a._wright(a)dom.com, tlui(a)apsc.com, Kara.Gibson(a)nmcco.com, Gary.Greer(a)pseg.com, "RE Supervisors" marienmj(a)songs.sce.com, foxkw(a)naesco.com, getiner(a)tva.gov, rlozano(a)stpegs.com, Ted_Powers(a)fpl.com, Ted_Powers(a)fpl.com, stanley_gardocki(a)dom.com, Brent_Robinson(a)fpl.com, gtglaser(a)pplweb.com, mharrison(a)amergenenerry.com, douglas.robinson(a)fpl.com, dbelton(a)scana.com, altinsle(a)southernco.com, dbentzi(a)entergy.com, tpayne(a)entergy.com, chhansf(a)wcnoc.com, sabolaj(a)westinghouse.com, Respvr(a)retaqs.com, Robert.McDonaldJr(a)exeloncorp.com, Harryl.Miller(a)exeloncorp.com, Herbert.Evans(a)constellation.com, VDMiller(a)cal.ameren.com, Puccir(a)firstenergycorp.com, dsttoltz(a)entergy.com, James.d.blakenship(a)constellation.com, trcabe(a)duke-energy.com, dwmiller2(a)aep.com, cjh1(a)page.com, jbement(a)constellation.com, karen.rogers(a)pgnmail.com, joey.rhodes(a)pgnmail.com, psdame(a)duke-energy.com, david.plennen(a)dom.com, tjcjerry(a)duke-energy.com, glholden(a)duke-energy.com, wsneed(a)apsc.com, Susanne.Ziegler(a)pseg.com, billngsd(a)songs.sce.com, pebblel(a)songs.sce.com, robert_sterritt(a)fpl.com, jgrant(a)southernco.com, leonard_rollings(a)dom.com, Dean.DiVittore(a)exeloncorp.com, jhunsicker(a)scana.com, rcbourne(a)southernco.com cc: Elizabeth.Young(a)exeloncorp.com Subject: [Respvr] MIDs questionnaire Greetings from Byron, At the end of a refueling outage, we "check out" the Moveable Incore Detector System (MIDS) prior to it being needed for the first flux map. The checkout is essentially like a flux map, but no data is taken - we run the detectors through all the passes to Top of Core to ensure that each thimble is accessible and that no other problems exist (or if problems are found, that they are fixed before the system is needed for the flux map). Currently, one of the prerequisites for this checkout is that Containment must be evacuated due to the possibility of personnel over-exposure from the MIDS. It is a challenge every outage to evacuate containment for this checkout. Therefore, we are looking at the possibility of evacuating only certain areas of containment when the MIDS are in use during the outage. This will not apply to at-power operations, as Containment will still be required to be free of personnel at those times. We are trying to get a preliminary feel for what the rest of the industry does in terms of using the MIDS while personnel are in Containment in an outage. (1) Do you checkout the system prior to its use in a flux map at the end of a refueling outage? (2) IF you do such a checkout, do you need evacuate containment, or can you run the MIDS while personnel are in containment? a) Are your incore drives located outside your bio wall? (3) If you do NOT evacuate Containment: a) how do you control personnel entry to the affected areas? b) what areas do you control? c) how did you get your site to accept this practice? (4) If possible, please supply a contact (name, phone, e-mail) of a knowledgeable Radiation Protection (RP) individual or Health Physicist (HP) at your site who we could contact for further information on this topic. Thanks! Frank Paslaski Exelon Nuclear Frank Paslaski,Radiation Protection Outage Planner Byron Generating Station 4450 North German Church Road Byron, IL 61010 Phone: 815-406-2732 offsite pager:815-480-8916 Fax: 815-234-5414 Email: Frank.Paslaski(a)exeloncorp.com **************************************************** ******************** This e-mail and any of its attachments may contain Exelon Corporation proprietary information, which is privileged, confidential, or subject to copyright belonging to the Exelon Corporation family of Companies. This e-mail is intended solely for the use of the individual or entity to which it is addressed. If you are not the intended recipient of this e-mail, you are hereby notified that any dissemination, distribution, copying, or action taken in relation to the contents of and attachments to this e-mail is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify the sender immediately and permanently delete the original and any copy of this e-mail and any printout. Thank You. ******************************************************************* *****_______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

MIDs questionnaire
by frank.paslaski＠exeloncorp.com 19 May '06

19 May '06

Greetings from Byron, At the end of a refueling outage, we "check out" the Moveable Incore Detector System (MIDS) prior to it being needed for the first flux map. The checkout is essentially like a flux map, but no data is taken - we run the detectors through all the passes to Top of Core to ensure that each thimble is accessible and that no other problems exist (or if problems are found, that they are fixed before the system is needed for the flux map). Currently, one of the prerequisites for this checkout is that Containment must be evacuated due to the possibility of personnel over-exposure from the MIDS. It is a challenge every outage to evacuate containment for this checkout. Therefore, we are looking at the possibility of evacuating only certain areas of containment when the MIDS are in use during the outage. This will not apply to at-power operations, as Containment will still be required to be free of personnel at those times. We are trying to get a preliminary feel for what the rest of the industry does in terms of using the MIDS while personnel are in Containment in an outage. (1) Do you checkout the system prior to its use in a flux map at the end of a refueling outage? (2) IF you do such a checkout, do you need evacuate containment, or can you run the MIDS while personnel are in containment? a) Are your incore drives located outside your bio wall? (3) If you do NOT evacuate Containment: a) how do you control personnel entry to the affected areas? b) what areas do you control? c) how did you get your site to accept this practice? (4) If possible, please supply a contact (name, phone, e-mail) of a knowledgeable Radiation Protection (RP) individual or Health Physicist (HP) at your site who we could contact for further information on this topic. Thanks! Frank Paslaski Exelon Nuclear Frank Paslaski,Radiation Protection Outage Planner Byron Generating Station 4450 North German Church Road Byron, IL 61010 Phone: 815-406-2732 offsite pager:815-480-8916 Fax: 815-234-5414 Email: Frank.Paslaski(a)exeloncorp.com ----------------------------------------- ******************************************************************* ***** This e-mail and any of its attachments may contain Exelon Corporation proprietary information, which is privileged, confidential, or subject to copyright belonging to the Exelon Corporation family of Companies. This e-mail is intended solely for the use of the individual or entity to which it is addressed. If you are not the intended recipient of this e-mail, you are hereby notified that any dissemination, distribution, copying, or action taken in relation to the contents of and attachments to this e-mail is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify the sender immediately and permanently delete the original and any copy of this e-mail and any printout. Thank You. ******************************************************************* *****

1 0

RE: [Respvr] Start Up sequence
by ALDAY, CLINT L 19 May '06

19 May '06

Non-Refueling: first dilute the RCS to the estimated critical rod position, then withdraw shutdown banks, then withdraw control rods to critical. (Your second option) Refueling: establish a boron concentration to perform an ARO CEA drop time (scram time) test and withdraw rods using 1/M to do that test. We then withdraw back to the last group (4 rods) inserted to 75" (50%) and dilute to critical. Clint Alday Waterford 3 -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of Hugh_E_McKenney(a)dom.com Sent: Thursday, May 18, 2006 8:19 AM To: respvr(a)retaqs.com Subject: [Respvr] Start Up sequence RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

RE: [Respvr] Start Up sequence
by MCCOY, JAIME H 18 May '06

18 May '06

ANO-1 (B&W) and ANO-2 (CE) dilutes/borates to boron concentration for S/D bank removal, pulls S/D banks, dilutes to ECP, then goes critical on rods. The reason I say "dilutes/borates" is depending on where you end up after the shutdown, you might have to continue to borate up to be able to meet requirements to pull S/D banks. Regards, Jaime H. McCoy ANO Reactor Engineering Supt. 479-858-5525 jmccoy(a)entergy.com -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com] On Behalf Of Hugh_E_McKenney(a)dom.com Sent: Thursday, May 18, 2006 8:19 AM To: respvr(a)retaqs.com Subject: [Respvr] Start Up sequence RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

Re: [Respvr] Start Up sequence
by paul_gurney＠fpl.com 18 May '06

18 May '06

Seabrook Dilute, withdraw s/d banks, withdraw control banks Paul Gurney Hugh_E_McKenney@d om.com To: respvr(a)retaqs.com Sent by: cc: respvr-bounces@re Subject: [Respvr] Start Up sequence taqs.com 05/18/2006 09:18 AM Please respond to "RE Supervisors" RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you. _______________________________________________ Respvr mailing list Respvr(a)retaqs.com http://www.keffective.com/mailman/listinfo/respvr

1 0

Start Up sequence
by Hugh_E_McKenney＠dom.com 18 May '06

18 May '06

RE Supervisors, Does your plant normally start up (non RFO) by withdrawing shutdown banks first, then diluting the RCS to the estimated critical rod position (Cb) then withdrawing control rods to critical? or Does your plant normally start up by first diluting the RCS to the estimated critical rod position (Cb), then withdrawing shutdown banks, then withdrawing control rods to critical? Thanks Hugh McKenney Dominion Resources Services, Inc. Reactor Engineering Supervisor Phone: 8-759-2359 or 860 447-1791 x2359 Email: Hugh_E_McKenney(a)Dom.com ----------------------------------------- CONFIDENTIALITY NOTICE: This electronic message contains information which may be legally confidential and/or privileged and does not in any case represent a firm ENERGY COMMODITY bid or offer relating thereto which binds the sender without an additional express written confirmation to that effect. The information is intended solely for the individual or entity named above and access by anyone else is unauthorized. If you are not the intended recipient, any disclosure, copying, distribution, or use of the contents of this information is prohibited and may be unlawful. If you have received this electronic transmission in error, please reply immediately to the sender that you have received the message in error, and delete it. Thank you.

1 0

RE: [Respvr] Ramp rates with and with out leaking fuel assemblies
by ronald.niederer＠exeloncorp.com 18 May '06

18 May '06

See below answers for Byron (Exelon) -----Original Message----- From: respvr-bounces(a)retaqs.com [mailto:respvr-bounces@retaqs.com]On Behalf Of Delk, Whiting S. Sent: Thursday, May 18, 2006 7:09 AM To: respvr(a)retaqs.com Cc: Lemons, James F. Subject: [Respvr] Ramp rates with and with out leaking fuel assemblies Please provide your PWR fuel duty limitations (both sound and leaking fuel, increasing and decreasing power, etc.). No leaking Fuel/Start up after refueling: 0 - 40% no limit (15 %/hr is planned rate) 40 - 75% 3 %/hr 75 -100% 0.5 %/hr Ramp rate up and Power break points at which ramp rate changs. No leaking fuel Normal Operations: 0 - 40% no limit (15 %/hr is planned rate) 40 - 75% 3 %/hr 75 - 90% 2 %/hr 90 -100% 1 %/hr Ramp rate down. 100 - 0% no limit (15 %/hr is planned rate) Ramp rate (and break points) return to RTP. see above Restrictions on Ramp rates with Leaking Fuel: Ramp rate down. DOWN 100 - 90% 3 %/hr 90 - 40% 10 %/hr 40 - 0% 15 %/hr Ramp rate (and break points) return to RTP. UP 0 - 20% 15 %/hr 20 - 40% 5 %/hr 40 - 75% 3 %/hr 75 - 90% 2 %/hr 90 -100% 1 %/hr Thanks for your assistance. I will repackage and send to responders. Thanks for your valuable time. Whiting S. Delk Reactor Engineering Supervisor Watts Bar Nuclear Plant ----------------------------------------- ******************************************************************* ***** This e-mail and any of its attachments may contain Exelon Corporation proprietary information, which is privileged, confidential, or subject to copyright belonging to the Exelon Corporation family of Companies. This e-mail is intended solely for the use of the individual or entity to which it is addressed. If you are not the intended recipient of this e-mail, you are hereby notified that any dissemination, distribution, copying, or action taken in relation to the contents of and attachments to this e-mail is strictly prohibited and may be unlawful. If you have received this e-mail in error, please notify the sender immediately and permanently delete the original and any copy of this e-mail and any printout. Thank You. ******************************************************************* *****

1 0

← Newer
1
...
5
6
7
8
9
10
11
12
13
Older →

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

Respvr